Thursday, January 12, 2012

Mechanical arrangement of internal gearboxes.


6
. To minimize unwanted movement between the compressor shaft bevel gear and radial driveshaft
(fig. 7-1)
bevel gear, caused by axial movement of the compressor shaft, the drive is taken by one of three basic methods (fig. 7-2). The least number of components is used when the compressor shaft bevel gear is mounted as close to the compressor shaft location bearing as possible, but a small amount of movement has to be accommodated within the meshing of the bevel gears. Alternatively, the compressor shaft bevel gear may be mounted on a stub shaft which has its own location bearing. The stub shaft is splined onto the compressor shaft which allows axial movement without affecting the bevel gear mesh. A more complex system utilizes an idler gear which meshes with the compressor shaft via straight spur gears, accommodating the axial movement, and drives the radial driveshaft via a bevel gear arrangement. The latter method was widely employed on early engines to overcome gear engagement difficulties at high speed.



7. To spread the load of driving accessory units, some engines take a second drive from the slower rotating low pressure shaft to a second external gearbox (fig. 7-1). This also has the advantage of locating the accessory units in two groups, thus overcoming the possibility of limited external space on the engine. When this method is used, an attempt is made to group the accessory units specific to the engine onto the high pressure system, since that is the first shaft to rotate, and the aircraft accessory units are driven by the low pressure system.A typical internal gearbox showing how both drives are taken is shown in fig.7-3

Radial driveshaft :


8. The purpose of a radial driveshaft is to transmit the drive from the internal gearbox to an accessory
unit or the external gearbox. It also serves to transmit the high torque from the starter to rotate the high
pressure system for engine starting purposes. The driveshaft may be direct drive or via an intermediate
gearbox (para. 14).

Fig. 7-2 Mechanical arrangement of internal
 gearboxes

9. To minimize the effect of the driveshaft passing through the compressor duct and disrupting the
airflow, it is housed within the compressor support structure. On by-pass engines, the driveshaft is
either housed in the outlet guide vanes or in a hollow streamlined radial fairing across the low pressure
compressor duct.

10. To reduce airflow disruption it is desirable to have the smallest driveshaft diameter as possible.
The smaller the diameter, the faster the shaft must rotate to provide the same power. However, this
raises the internal stress and gives greater dynamic problems which result in vibration. A long radial
drive shaft usually requires a roller bearing situated halfway along its length to give smooth running. This
allows a rotational speed of approximately 25,000 r.p.m. to be achieved with a shaft diameter of less
than 1.5 inch without encountering serious vibration problems.

5 comments:

  1. Good Post and informative one. Thank you for sharing this good article.
    Bevel Gear Suppliers

    ReplyDelete
  2. Thank you for sharing informative blog , It is really helpful to everyone. bevel gear suppliers

    ReplyDelete
  3. Hello Sir! I read your blog whose is a very informative and knowledgeable about Gearboxes Manufacturers In India. So, thanks for sharing information with us. So here, Want to tell you about your Gearbox Manufacturers in India here.

    ReplyDelete
  4. Gear Box Manufacturer
    Spear Gear Manufacturer in India
    Conveyor Belt Manufacturer
    Prakash Eng. & Gear company is manufacturer and suppliers of different type of Conveyor Plant Manufacturer in India, and trusted Idler Roller Manufacturer in India We provide impact idler, troughing roller, conveyor belt idlers, carrying idler roller, gravity conveyors, return idlers, rubber-coated idler rollers and other conveyor parts at market leading prices Crusher Gears, Bolt, Stud, High light, Gear Box, Crusher Gears, Bolt, Stud, High light, Gear Box, Chain Wheel & Duplex, Concrete Mixer, Chain Wheel & Duplex, Concrete Mixer also any spare Parts of machine.

    ReplyDelete